Author Topic: Help with trigger  (Read 8493 times)

Tags:
  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #15 on: 10 Sep 2013, 16:07 »
Hi,

Seems to be starting at the 30sec after the off rather than at wait...

  • Moderator
  • Posts: 3597
*
Re: Help with trigger
« Reply #16 on: 10 Sep 2013, 16:32 »
Hi
It's working fine.
It sets markets inplay refresh rate to 0.3 33 seconds before end of race.

You need to be refreshing (monitoring) the market before the off so it can pick up inplay time required for the calculations.

Also default idle and inplay rates should be 1 second or quicker for accurate timing.

but it's working OK.
Please read the following disclaimer with regards to the information you may request and obtain on our forum. This specifically concerns trigger files and various instructions as to how to implement a strategy.

  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #17 on: 10 Sep 2013, 16:56 »
I had the refresh trigger in another block when testing- does this make the difference?

  • Moderator
  • Posts: 3597
*
Re: Help with trigger
« Reply #18 on: 10 Sep 2013, 17:18 »
It should not make any difference. Attached is the one I was testing, which effectively is the same as yours and it works fine.

Check the following settings:
Settings > Betting Options > Banking > all unticked
Settings > Betting Options > Triggers > No triggering till unticked
Settings > Monitoring Options > Start monitoring x before beginning ticked
Settings > Monitoring Options > Idle and inplay refresh rates 1 sec
Settings > Test Mode > Delay placing... unticked

What distance race did you test on. If 5f it will trigger around 30s in.
Please read the following disclaimer with regards to the information you may request and obtain on our forum. This specifically concerns trigger files and various instructions as to how to implement a strategy.

  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #19 on: 11 Sep 2013, 09:48 »
My idle refresh was at 2secs and i had half sec delay in test.

Will try again this afty....

Will the test delay effect the way it works much? as i use the delay so when i go live the results are similar...

  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #20 on: 11 Sep 2013, 15:55 »
Yes you are right- it works just as it should.

Thanks for all your help


  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #21 on: 12 Sep 2013, 07:45 »
Is it possible to set a command for the final third? 

I thought "sel trigger expression timetoend is less than racetime/3" would work but it doesn't?

  • Moderator
  • Posts: 3597
*
Re: Help with trigger
« Reply #22 on: 12 Sep 2013, 10:42 »
Hi
Just waiting for some markets to test it. Should be up later.
Please read the following disclaimer with regards to the information you may request and obtain on our forum. This specifically concerns trigger files and various instructions as to how to implement a strategy.

  • Moderator
  • Posts: 3597
*
Re: Help with trigger
« Reply #23 on: 12 Sep 2013, 14:35 »
Hi
In this version the race distance is multiplied by 0.66 (you can adjust this in a constant)
so when TimeToEnd is zero, we are actually two thirds into the race and the trigger will fire.
The wait variable should be set close to zero.

Please try in test mode.
Please read the following disclaimer with regards to the information you may request and obtain on our forum. This specifically concerns trigger files and various instructions as to how to implement a strategy.

  • All members
  • Posts: 35
  • Gender: Male
Re: Help with trigger
« Reply #24 on: 12 Sep 2013, 14:49 »
Thanks again Mark ;D

 

Please note, BetFair is seems to be currently OFFLINE